Fire Rated Downlight GU10 Twist and Lock Fixed - Quick Connector, Loop In/Out - Chrome Finish
- Independently tested to ensure it conforms to all relevant British Standards
- Fire-rated for 90 minutes
- Gorgeous polished chrome finish
- Made of die-cast aluminium
- 5-year warranty
Ideal for 90 Minute Ceilings
This LED downlight is fire-rated to 90 minutes of protection, meaning the hole you cut to install your lights is resealed, and your ceiling is reinforced to extend the time when the fire will spread (in this case, by 90 minutes). This precautionary measure will enable you and your family to exit safely, and the damage to your home’s structure will not be as bad.
Only a fire-rated downlight can restore your ceiling fire integrity compromised by cutting a hole. It’s because a fire-rated fitting is made with an intumescent pad that activates when exposed to a specific temperature, allowing it to block even the tiny crevices that the fire may slip through!
Gorgeous Polished Chrome Bezel
With its simple round bezel and gorgeous polished chrome finish, this LED downlight does not have difficulty fitting in with whatever aesthetic you have! Whether it's a traditional or modern layout, this LED downlight can blend in effortlessly as if it was intentionally added to the design!
If you love restyling your interior when the seasons change, using a minimal-looking lighting fixture light, like this LED downlight, will benefit your more. With its basic appearance, you’ll be able to try out various design scheme combinations and decorations that may not go well with a customised lighting fixture. So, consider incorporating this LED downlight into your lighting system if you're after flexibility and creative freedom!
Top-Quality! Constructed from Die-Cast Aluminium
This LED downlight is constructed from die-cast aluminium, so you can expect that it will not rust or tarnish even after using it for years! In addition, this fitting is low-maintenance, so you won’t be constantly bothered about its upkeep. Just wipe it down occasionally to remove any dust or dirt build-up that may be blocking the light from being delivered to the surfaces below.
Ceiling lights are more challenging to install than table lamps and floor lamps you typically plugin. If you end up with low-quality fixtures that break down quickly, you’ll have to buy replacements and redo the installation process. So, save yourself from all the hassles with this LED downlight!
The installation of this LED downlight is straightforward and quick as it's designed with everything that streamlines the process! It has a twist and lock mechanism (allowing rapid bulb changes) and push-fit terminal blocks for easy loop-in/out (no need for screws). With this, you can wire each downlight in series instead of individually connecting them to the primary power supply!
Aside from that, it’s mains powered; therefore, you don’t need to purchase a separate driver or transformer to make it work. All you have to do is plan the position of the fixtures, trim the cut-out hole, wire it directly to the mains circuit, and add a bulb of your choice. That’s it!
Works with a GU10 Bulb
You can use any GU10 bulb with this LED downlight because it's made with a GU10 lamp holder. Although, since it's a dimmable fixture, pairing it with a dimmable GU10 bulb and a compatible dimmer switch will enable you to utilise its dimming function!
As for the GU10 bulb, it's available in cool white, natural white and warm white light! Cool white and natural white are both ideal for task lighting. The only difference between the two colours is cool white has a crisp bluish tone, while natural white has no shades of blue or yellow. Alternatively, warm white light is suitable for ambient lighting because its yellowish tint can stage a cosy and relaxing vibe!
Knowing the dimensions of a lighting fixture is necessary to guarantee a flawless and hassle-free installation. Say you improvise and estimate the measurements you need to consider when installing this LED downlight. There’s a high possibility that the cut-out hole will be too small that the fixture won’t fit or too big that it’ll fall off! Your downlight may also end up protruding instead of sitting snuggly against your ceiling because you did not consider its height and the available ceiling void!
So, take note that this LED downlight is 130mm tall with an 85mm diameter and requires a 75mm cut-out hole! Follow these measurements precisely, and you’ll have no problems when mounting!
|Quick Order Code||FRFC|
|Cut Out Hole||75mm|