Simple Lighting Co.
0151 375 92100333 443 2465Order & Advice line
- Product Description
- Specifications
- Reviews
- Delivery & Returns
- Related Products
Product Description
Die-Cast Fire Rated Downlight, GU10 In A Brushed Chrome Finish
Main Features;
- Supplied including Loop In/Out quick connector to speed up installation
- Die-Cast Aluminium, meaning it is built to an extremely high standard
- Twist & Lock, meaning changing the bulb is simple and there are no annoying springs to do so
- Independently tested to conform to all relevant BS standards. Further details below.
- A quality fire rated downlight, this product listing is for one which is of a brushed chrome finish (Brushed chrome is also known as satin chrome). However, we supply these also in Polished Chrome and White finish.
Our downlights meet all relevant BS standards including;
- Tested to 90 minutes protection
- Tested and accessed to BS 476, Parts 21, 22 & 23
- Part "E" compliant (Acoustics)
- Since this is a GU10 fitted, it is 230v Mains powered. No transformer is needed to run this downlight. Connect directly to mains
These Downlights are fully compatible with the latest LED GU10 Bulbs, we are specialists in LED technology and offer LED Bulbs from only £1.99 which you can add to your order when Adding to Basket.
Your options are as follows:
- 5w GU10 LED - 320 Lumens - Replaces a standard 50w Halogen Bulb.
- 5w Dimmable GU10 LED - 350 Lumens - Replaces a standard 50w Halogen Bulb.
- 7w GU10 LED - 530 Lumens - Replaces a 60-70w Halogen Bulb.
If you would prefer to buy this downlight without a GU10 LED or select your own GU10 select that No Bulb is required when adding to basket and visit our GU10 LED Bulb Page.
Product Features;
- 230v Mains
- Max wattage, 35w (Flammable Surfaces), 50w (non-flammable surfaces)
- IP20 Rated
- Meets all relevant BS regulations
- Brushed Finish (Also known as satin chrome)
- Steel Can
- Diameter - 85mm
- Total Length - 110mm (Without Connector Block) 130mm (With)
- Cut Out - 75mm
- Independently tested to conform to BS Standards By TUV.
Specifications
-
Product Range Die-Cast Range
-
Type of Fitting Fixed Downlight
-
SKU FGFSDC
-
Height 110mm (Without Terminal Block) 130mm (With Terminal) The overall height of the product at the tallest point.
-
Diameter 85mm The measurement across the face of the light source. Normally in mm unless other stated.
-
Cutout Size 75mm The size of the cutout required to install the light. This is normally measure in mm unless otherwise stated.
-
Delivery Time Available Next Day if Ordered Before 3pm
-
Finish Brushed Chrome The overall visible finish of the product. Such as stainless steel, chrome, white etc.
-
Dimmable Yes Whether the brightness is dimmable or not. Some products are dimmable via specialist remote control systems we supply. Whereas some products are dimmable with mains voltage wall dimmer.
-
IP20 Ingress protection rating. Classifies the degree of protection against water and dust.
-
Lamp Base GU10 Indicates the size of the electrical connection at the bottom of the light source. Such as screw or bayonet etc. If you are confused with what you require please feel free to contact us for us.
-
Maximum Load 35W Flammable Surfaces / 50W Non Flammable Surfaces The maximum electrical load that the product is manufactured to accept. Normally measured in Watts or AMP. EG, if you have a product which is 150w and lights which are 50w each then 3 x 50w = 150w which is the maximum load.
For delivery or returns information, please refer to the page below.
